Commit "bb6abcf: ARM: OMAP2+: Kconfig: convert SOC_OMAPAM33XX to
SOC_AM33XX" and "3395955: ARM: OMAP2+: Kconfig: convert
SOC_OMAPTI81XX to SOC_TI81XX" has changed the SOC config for AM33XX
and TI81XX as shown below
CONFIG_SOC_OMAPAM33XX --> CONFIG_SOC_AM33XX
CONFIG_SOC_OMAPTI81XX --> CONFIG_SOC_TI81XX
So updating the same at musb driver for AM33XX and TI81XX platforms.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Otherwise you could run into:
WARN_ON in numa_register_memblks(), because node_possible_map is zero
References: https://bugzilla.novell.com/show_bug.cgi?id=757888
On this machine (ProLiant ML570 G3) the SRAT table contains:
- No processor affinities
- One memory affinity structure (which is set disabled)
CC: Per Jessen <per@opensuse.org>
CC: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
User space access must always go through uaccess accessors, since on
classic m68k user space and kernel space are completely separate.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Tested-by: Thorsten Glaser <tg@debian.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@vger.kernel.org
Depending on layout and ARCH, ORE has some limits on max IO sizes
which is communicated on (what else) ore_layout->max_io_length,
which is always stripe aligned.
This was considered as the pg_test boundary for splitting and starting
a new IO.
But in the case of a long IO where the start offset is not aligned
what would happen is that both end of IO[N] and start of IO[N+1]
would be unaligned, causing each IO boundary parity unit to be
calculated and written twice.
So what we do in this patch is split the very start of an unaligned
IO, up to a stripe boundary, and then next IO's can continue fully
aligned til the end.
We might be sacrificing the case where the full unaligned IO would
fit within a single max_io_length, but the sacrifice is well worth
the elimination of double calculation and parity units IO.
Actually the sacrificing is marginal and is almost unmeasurable.
TODO:
If we know the total expected linear segment that will
be received, at pg_init, we could use that information
in many places:
1. blocks-layout get_layout write segment size
2. Better mds-threshold
3. In above situation for a better clean split
I will do this in future submission.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
since the only user of nfs4_proc_layoutget is send_layoutget, which
ignores its return value, there is no reason to return any value.
Signed-off-by: Idan Kedar <idank@tonian.com>
Signed-off-by: Benny Halevy <bhalevy@tonian.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
we have encountered a bug whereby reading a lot of files (copying
fedora's /bin) from a pNFS mount and hitting Ctrl+C in the middle caused
a general protection fault in xdr_shrink_bufhead. this function is
called when decoding the response from LAYOUTGET. the decoding is done
by a worker thread, and the caller of LAYOUTGET waits for the worker
thread to complete.
hitting Ctrl+C caused the synchronous wait to end and the next thing the
caller does is to free the pages, so when the worker thread calls
xdr_shrink_bufhead, the pages are gone. therefore, the cleanup of these
pages has been moved to nfs4_layoutget_release.
Signed-off-by: Idan Kedar <idank@tonian.com>
Signed-off-by: Benny Halevy <bhalevy@tonian.com>
Cc: stable@vger.kernel.org
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Pull OLPC platform updates from Andres Salomon:
"These move the OLPC Embedded Controller driver out of
arch/x86/platform and into drivers/platform/olpc.
OLPC machines are now ARM-based (which means lots of x86 and ARM
changes), but are typically pretty self-contained.. so it makes more
sense to go through a separate OLPC tree after getting the appropriate
review/ACKs."
* 'for-linus-3.6' of git://dev.laptop.org/users/dilinger/linux-olpc:
x86: OLPC: move s/r-related EC cmds to EC driver
Platform: OLPC: move global variables into priv struct
Platform: OLPC: move debugfs support from x86 EC driver
x86: OLPC: switch over to using new EC driver on x86
Platform: OLPC: add a suspended flag to the EC driver
Platform: OLPC: turn EC driver into a platform_driver
Platform: OLPC: allow EC cmd to be overridden, and create a workqueue to call it
drivers: OLPC: update various drivers to include olpc-ec.h
Platform: OLPC: add a stub to drivers/platform/ for the OLPC EC driver
Pull arm-soc Marvell Orion device-tree updates from Olof Johansson:
"This contains a set of device-tree conversions for Marvell Orion
platforms that were staged early but took a few tries to get the
branch into a format where it was suitable for us to pick up.
Given that most people working on these platforms are hobbyists with
limited time, we were a bit more flexible with merging it even though
it came in late."
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
ARM: Kirkwood: Replace mrvl with marvell
ARM: Kirkwood: Describe GoFlex Net LEDs and SATA in DT.
ARM: Kirkwood: Describe Dreamplug LEDs in DT.
ARM: Kirkwood: Describe iConnects LEDs in DT.
ARM: Kirkwood: Describe iConnects temperature sensor in DT.
ARM: Kirkwood: Describe IB62x0 LEDs in DT.
ARM: Kirkwood: Describe IB62x0 gpio-keys in DT.
ARM: Kirkwood: Describe DNS32? gpio-keys in DT.
ARM: Kirkwood: Move common portions into a kirkwood-dnskw.dtsi
ARM: Kirkwood: Replace DNS-320/DNS-325 leds with dt bindings
ARM: Kirkwood: Describe DNS325 temperature sensor in DT.
ARM: Kirkwood: Use DT to configure SATA device.
ARM: kirkwood: use devicetree for SPI on dreamplug
ARM: kirkwood: Add LS-XHL and LS-CHLv2 support
ARM: Kirkwood: Initial DTS support for Kirkwood GoFlex Net
ARM: Kirkwood: Add basic device tree support for QNAP TS219.
ATA: sata_mv: Add device tree support
ARM: Orion: DTify the watchdog timer.
ARM: Orion: Add arch support needed for I2C via DT.
ARM: kirkwood: use devicetree for orion-spi
...
Conflicts:
drivers/watchdog/orion_wdt.c
Pull arm-soc cpuidle enablement for OMAP from Olof Johansson:
"Coupled cpuidle was meant to merge for 3.5 through Len Brown's tree,
but didn't go in because the pull request ended up rejected. So it
just got merged, and we got this staged branch that enables the
coupled cpuidle code on OMAP.
With a stable git workflow from the other maintainer we could have
staged this earlier, but that wasn't the case so we have had to merge
it late.
The alternative is to hold it off until 3.7 but given that the code is
well-isolated to OMAP and they are eager to see it go in, I didn't
push back hard in that direction."
* tag 'pm2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: OMAP4: CPUidle: Open broadcast clock-event device.
ARM: OMAP4: CPUidle: add synchronization for coupled idle states
ARM: OMAP4: CPUidle: Use coupled cpuidle states to implement SMP cpuidle.
ARM: OMAP: timer: allow gp timer clock-event to be used on both cpus
Pull ARM SoC fixes from Olof Johansson:
"A few fixes for merge window fallout, and a bugfix for timer resume on
PRIMA2."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: mmp: add missing irqs.h
arm: mvebu: fix typo in .dtsi comment for Armada XP SoCs
ARM: PRIMA2: delete redundant codes to restore LATCHED when timer resumes
ARM: mxc: Include missing irqs.h header
Pull SuperH fixes from Paul Mundt.
* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh: (24 commits)
sh: explicitly include sh_dma.h in setup-sh7722.c
sh: ecovec: care CN5 VBUS if USB host mode
sh: sh7724: fixup renesas_usbhs clock settings
sh: intc: initial irqdomain support.
sh: pfc: Fix up init ordering mess.
serial: sh-sci: fix compilation breakage, when DMA is enabled
dmaengine: shdma: restore partial transfer calculation
sh: modify the sh_dmae_slave_config for RSPI in setup-sh7757
sh: Fix up recursive fault in oops with unset TTB.
sh: pfc: Build fix for pinctrl_remove_gpio_range() changes.
sh: select the fixed regulator driver on several boards
sh: ecovec: switch MMC power control to regulators
sh: add fixed voltage regulators to se7724
sh: add fixed voltage regulators to sdk7786
sh: add fixed voltage regulators to rsk
sh: add fixed voltage regulators to migor
sh: add fixed voltage regulators to kfr2r09
sh: add fixed voltage regulators to ap325rxa
sh: add fixed voltage regulators to sh7757lcr
sh: add fixed voltage regulators to sh2007
...
Pull additional md update from NeilBrown:
"This contains a few patches that depend on plugging changes in the
block layer so needed to wait for those.
It also contains a Kconfig fix for the new RAID10 support in dm-raid."
* tag 'md-3.6' of git://neil.brown.name/md:
md/dm-raid: DM_RAID should select MD_RAID10
md/raid1: submit IO from originating thread instead of md thread.
raid5: raid5d handle stripe in batch way
raid5: make_request use batch stripe release
Pull two ceph fixes from Sage Weil:
"The first patch fixes up the old crufty open intent code to use the
atomic_open stuff properly, and the second fixes a possible null deref
and memory leak with the crypto keys."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
libceph: fix crypto key null deref, memory leak
ceph: simplify+fix atomic_open
Pull ecryptfs fixes from Tyler Hicks:
- Fixes a bug when the lower filesystem mount options include 'acl',
but the eCryptfs mount options do not
- Cleanups in the messaging code
- Better handling of empty files in the lower filesystem to improve
usability. Failed file creations are now cleaned up and empty lower
files are converted into eCryptfs during open().
- The write-through cache changes are being reverted due to bugs that
are not easy to fix. Stability outweighs the performance
enhancements here.
- Improvement to the mount code to catch unsupported ciphers specified
in the mount options
* tag 'ecryptfs-3.6-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
eCryptfs: check for eCryptfs cipher support at mount
eCryptfs: Revert to a writethrough cache model
eCryptfs: Initialize empty lower files when opening them
eCryptfs: Unlink lower inode when ecryptfs_create() fails
eCryptfs: Make all miscdev functions use daemon ptr in file private_data
eCryptfs: Remove unused messaging declarations and function
eCryptfs: Copy up POSIX ACL and read-only flags from lower mount
Pull CIFS update from Steve French:
"Adds SMB2 rmdir/mkdir capability to the SMB2/SMB2.1 support in cifs.
I am holding up a few more days on merging the remainder of the
SMB2/SMB2.1 enablement although it is nearing review completion, in
order to address some review comments from Jeff Layton on a few of the
subsequent SMB2 patches, and also to debug an unrelated cifs problem
that Pavel discovered."
* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
CIFS: Add SMB2 support for rmdir
CIFS: Move rmdir code to ops struct
CIFS: Add SMB2 support for mkdir operation
CIFS: Separate protocol specific part from mkdir
CIFS: Simplify cifs_mkdir call
brcmsmac cannot call freq_reg_info() during channel changes as it does
not hold cfg80211_lock, and as a result it generates a lockdep warning.
freq_reg_info() is being used to determine whether OFDM is allowed on
the current channel, so we can avoid the errant call by using the new
IEEE80211_CHAN_NO_OFDM for this purpose instead.
Reported-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The if_sdio_card structure was never being freed, and neither
was the command structure used for association.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On an OLPC XO-1.5 we have seen the following situation:
- the system starts going into suspend
- no wake params are set, so the mmc layer removes the card
- during remove, we send a command to the card
- that command fails, causing if_sdio's reset method to try and remove
the mmc card in attempt to reset it
- the mmc layer is not happy about being asked to remove a card that
it is already removing, and the kernel crashes
While the MMC layer could possibly be taught to behave better here,
it also seems sensible for libertas not to try and reset a card if
we're in the process of removing it anyway.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Borislav Petkov reports that the new warning added in commit
88fdf75d1b ("mm: warn if pg_data_t isn't initialized with zero")
triggers for him, and it is the node_start_pfn field that has already
been initialized once.
The call trace looks like this:
x86_64_start_kernel ->
x86_64_start_reservations ->
start_kernel ->
setup_arch ->
paging_init ->
zone_sizes_init ->
free_area_init_nodes ->
free_area_init_node
and (with the warning replaced by debug output), Borislav sees
On node 0 totalpages: 4193848
DMA zone: 64 pages used for memmap
DMA zone: 6 pages reserved
DMA zone: 3890 pages, LIFO batch:0
DMA32 zone: 16320 pages used for memmap
DMA32 zone: 798464 pages, LIFO batch:31
Normal zone: 52736 pages used for memmap
Normal zone: 3322368 pages, LIFO batch:31
free_area_init_node: pgdat->node_start_pfn: 4423680 <----
On node 1 totalpages: 4194304
Normal zone: 65536 pages used for memmap
Normal zone: 4128768 pages, LIFO batch:31
free_area_init_node: pgdat->node_start_pfn: 8617984 <----
On node 2 totalpages: 4194304
Normal zone: 65536 pages used for memmap
Normal zone: 4128768 pages, LIFO batch:31
free_area_init_node: pgdat->node_start_pfn: 12812288 <----
On node 3 totalpages: 4194304
Normal zone: 65536 pages used for memmap
Normal zone: 4128768 pages, LIFO batch:31
so remove the bogus warning for now to avoid annoying people. Minchan
Kim is looking at it.
Reported-by: Borislav Petkov <bp@amd64.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
arch/arm/mach-mmp/gplugd.c:195:13: error: ‘MMP_NR_IRQS’ undeclared here
(not in a function)
make[1]: *** [arch/arm/mach-mmp/gplugd.o] Error 1
Include <mach/irqs.h> to fix this issue.
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The comment was wrongly referring to Armada 370 while the file is
related to Armada XP.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The only way to write LATCHED registers to write LATCH_BIT to LATCH register,
that will latch COUNTER into LATCHED.e.g.
writel_relaxed(SIRFSOC_TIMER_LATCH_BIT, sirfsoc_timer_base +
SIRFSOC_TIMER_LATCH);
Writing values to LATCHED registers directly is useless at all.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Avoid crashing if the crypto key payload was NULL, as when it was not correctly
allocated and initialized. Also, avoid leaking it.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
ASoC: Additional updates for 3.6
A few updates for issues discovered during the merge window, the main
one being the fix for the issues with defaulting to use of regmap
without properly checking if there was I/O in place already.
The initial ->atomic_open op was carried over from the old intent code,
which was incomplete and didn't really work. Replace it with a fresh
method. In particular:
* always attempt to do an atomic open+lookup, both for the create case
and for lookups of existing files.
* fix symlink handling by returning 1 to the VFS so that we can follow
the link to its destination. This fixes a longstanding ceph bug (#2392).
Signed-off-by: Sage Weil <sage@inktank.com>
When we release pages back during bootup:
Freeing 9d-100 pfn range: 99 pages freed
Freeing 9cf36-9d0d2 pfn range: 412 pages freed
Freeing 9f6bd-9f6bf pfn range: 2 pages freed
Freeing 9f714-9f7bf pfn range: 171 pages freed
Freeing 9f7e0-9f7ff pfn range: 31 pages freed
Freeing 9f800-100000 pfn range: 395264 pages freed
Released 395979 pages of unused memory
We then try to populate those pages back. In the P2M tree however
the space for those leafs must be reserved - as such we use extend_brk.
We reserve 8MB of _brk space, which means we can fit over
1048576 PFNs - which is more than we should ever need.
Without this, on certain compilation of the kernel we would hit:
(XEN) domain_crash_sync called from entry.S
(XEN) CPU: 0
(XEN) RIP: e033:[<ffffffff818aad3b>]
(XEN) RFLAGS: 0000000000000206 EM: 1 CONTEXT: pv guest
(XEN) rax: ffffffff81a7c000 rbx: 000000000000003d rcx: 0000000000001000
(XEN) rdx: ffffffff81a7b000 rsi: 0000000000001000 rdi: 0000000000001000
(XEN) rbp: ffffffff81801cd8 rsp: ffffffff81801c98 r8: 0000000000100000
(XEN) r9: ffffffff81a7a000 r10: 0000000000000001 r11: 0000000000000003
(XEN) r12: 0000000000000004 r13: 0000000000000004 r14: 000000000000003d
(XEN) r15: 00000000000001e8 cr0: 000000008005003b cr4: 00000000000006f0
(XEN) cr3: 0000000125803000 cr2: 0000000000000000
(XEN) ds: 0000 es: 0000 fs: 0000 gs: 0000 ss: e02b cs: e033
(XEN) Guest stack trace from rsp=ffffffff81801c98:
.. which is extend_brk hitting a BUG_ON.
Interestingly enough, most of the time we are not going to hit this
b/c the _brk space is quite large (v3.5):
ffffffff81a25000 B __brk_base
ffffffff81e43000 B __brk_limit
= ~4MB.
vs earlier kernels (with this back-ported), the space is smaller:
ffffffff81a25000 B __brk_base
ffffffff81a7b000 B __brk_limit
= 344 kBytes.
where we would certainly hit this and hit extend_brk.
Note that git commit c3d93f8801
(xen: populate correct number of pages when across mem boundary (v2))
exposed this bug).
[v1: Made it 8MB of _brk space instead of 4MB per Jan's suggestion]
CC: stable@vger.kernel.org #only for 3.5
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
_ios_obj() is accessed by group_index not device_table index.
The oc->comps array is only a group_full of devices at a time
it is not like ore_comp_dev() which is indexed by a global
device_table index.
This did not BUG until now because exofs only uses a single
COMP for all devices. But with other FSs like PanFS this is
not true.
This bug was only in the write_path, all other users were
using it correctly
[This is a bug since 3.2 Kernel]
CC: Stable Tree <stable@kernel.org>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
exofs_max_io_pages should just use the ORE's
calculated layout->max_io_length,
And avoid unnecessary BUGs, calculations made here were
also a layering violation.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Restore the default state to the "beacon_found" flag when
the channel flags are restored. Otherwise, we can end up
with a channel that we can no longer transmit on even when
we can see beacons on that channel.
Signed-off-by: Paul Stewart <pstew@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently the only way for wireless drivers to tell whether or not OFDM
is allowed on the current channel is to check the regulatory
information. However, this requires hodling cfg80211_mutex, which is not
visible to the drivers.
Other regulatory restrictions are provided as flags in the channel
definition, so let's do similarly with OFDM. This patch adds a new flag,
IEEE80211_CHAN_NO_OFDM, to tell drivers that OFDM on a channel is not
allowed. This flag is set on any channels for which regulatory indicates
that OFDM is prohibited.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is very common for the end of the file to be unaligned on
stripe size. But since we know it's beyond file's end then
the XOR should be preformed with all zeros.
Old code used to just read zeros out of the OSD devices, which is a great
waist. But what scares me more about this situation is that, we now have
pages attached to the file's mapping that are beyond i_size. I don't
like the kind of bugs this calls for.
Fix both birds, by returning a global ZERO_PAGE, if offset is beyond
i_size.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Exofs has the '->write_super()' handler and makes some use of the '->s_dirt'
superblock flag, but it really needs neither of them because it never sets
's_dirt' to one which means the VFS never calls its '->write_super()' handler.
Thus, remove both.
Note, I am trying to remove both 's_dirt' and 'write_super()' from VFS
altogether once all users are gone.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
readpage_strip can be called from several code paths all of which
require that the page be locked before any operations are carried
out.
Since we export the exofs_readpage callback to the VFS, add a
BUG_ON to check for PageLocked(page) to make sure that this
understanding is never compromised.
Signed-off-by: Kautuk Consul <consul.kautuk@gmail.com>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Check if the chip has provided a write operation (which is mandatory for
I/O) rather than looking for control data as some of the MFDs use a global
for this. Also skip the attempt if there's no regmap available by device
in case things get confused by the attempt to default.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
