Merge tag 'riscv-dt-for-v6.19' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/dt

RISC-V Devicetrees for v6.19 MAINTAINERS: There's some re-jigging of things to reduce duplication, by moving me into the StarFive entry and my tree into the Microchip one. The other platforms that I look after (SiFive and Canaan) are marked as Odd Fixes to better represent their status. Nothing functionally changes. Microchip: Add adc and mmc nodes for the Beagle-V Fire. SiFive: Add pwm fans to the unmatched board. StarFive: Add the Orange PI RV board, another VisionFive 2 derived SBC. This required moving a mmc related nodes out of the common file, into <board>.dts. Yet more things moved out of the common file when the VisionFive 2 Lite boards were added, which use the JH7110S SoC instead of the JH7110. The difference here between SoCs is just temperature and frequency ranges, but the boards differ enough that the pool of common nodes decreases a little further. There's an eMMC and an SD variant here, that are different SKUs, bringing the total new StarFive boards to three. Signed-off-by: Conor Dooley <conor.dooley@microchip.com> * tag 'riscv-dt-for-v6.19' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux: riscv: dts: starfive: add Orange Pi RV dt-bindings: riscv: starfive: add xunlong,orangepi-rv riscv: dts: starfive: Add VisionFive 2 Lite eMMC board device tree riscv: dts: starfive: Add VisionFive 2 Lite board device tree riscv: dts: starfive: Add common board dtsi for VisionFive 2 Lite variants riscv: dts: starfive: jh7110-common: Move out some nodes to the board dts dt-bindings: riscv: Add StarFive JH7110S SoC and VisionFive 2 Lite board MAINTAINERS: degrade RISC-V MISC SOC SUPPORT to Odd Fixes MAINTAINERS: add tree to RISC-V Microchip entry MAINTAINERS: remove patchwork from RISC-V MISC SOC SUPPORT MAINTAINERS: add Conor to StarFive entry riscv: dts: sifive: unmatched: Add PWM controlled fans riscv: dts: microchip: enable qspi adc/mmc-spi-slot on BeagleV Fire dts: starfive: jh7110-common: split out mmc0 reset pins from common into boards Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2025-11-27 22:49:31 +01:00
parent ce48af13e6 5b70764e10
commit 3aa9940035
17 changed files with 528 additions and 23 deletions
--- a/Documentation/devicetree/bindings/riscv/starfive.yaml
+++ b/Documentation/devicetree/bindings/riscv/starfive.yaml
@@ -33,8 +33,15 @@ properties:
              - pine64,star64
              - starfive,visionfive-2-v1.2a
              - starfive,visionfive-2-v1.3b
+              - xunlong,orangepi-rv
          - const: starfive,jh7110

+      - items:
+          - enum:
+              - starfive,visionfive-2-lite
+              - starfive,visionfive-2-lite-emmc
+          - const: starfive,jh7110s
+
 additionalProperties: true

 ...
--- a/9
+++ b/9
@@ -22110,6 +22110,7 @@ M:	Conor Dooley <conor.dooley@microchip.com>
 M:	Daire McNamara <daire.mcnamara@microchip.com>
 L:	linux-riscv@lists.infradead.org
 S:	Supported
+T:	git https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux.git/ (dts, soc, firmware)
 F:	Documentation/devicetree/bindings/clock/microchip,mpfs*.yaml
 F:	Documentation/devicetree/bindings/gpio/microchip,mpfs-gpio.yaml
 F:	Documentation/devicetree/bindings/i2c/microchip,corei2c.yaml
@@ -22140,13 +22141,10 @@ F:	include/soc/microchip/mpfs.h
 RISC-V MISC SOC SUPPORT
 M:	Conor Dooley <conor@kernel.org>
 L:	linux-riscv@lists.infradead.org
-S:	Maintained
-Q:	https://patchwork.kernel.org/project/linux-riscv/list/
+S:	Odd Fixes
 T:	git https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux.git/
 F:	arch/riscv/boot/dts/canaan/
-F:	arch/riscv/boot/dts/microchip/
 F:	arch/riscv/boot/dts/sifive/
-F:	arch/riscv/boot/dts/starfive/

 RISC-V PMU DRIVERS
 M:	Atish Patra <atish.patra@linux.dev>
@@ -24471,7 +24469,10 @@ F:	drivers/crypto/starfive/

 STARFIVE DEVICETREES
 M:	Emil Renner Berthing <kernel@esmil.dk>
+M:	Conor Dooley <conor@kernel.org>
+L:	linux-riscv@lists.infradead.org
 S:	Maintained
+T:	git https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux.git/
 F:	arch/riscv/boot/dts/starfive/

 STARFIVE DWMAC GLUE LAYER
--- a/arch/riscv/boot/dts/microchip/mpfs-beaglev-fire.dts
+++ b/arch/riscv/boot/dts/microchip/mpfs-beaglev-fire.dts
@@ -79,6 +79,26 @@

 };

+&gpio0 {
+	interrupts = <13>, <14>, <15>, <16>,
+		     <17>, <18>, <19>, <20>,
+		     <21>, <22>, <23>, <24>,
+		     <25>, <26>;
+	ngpios = <14>;
+	status = "okay";
+};
+
+&gpio1 {
+	interrupts = <27>, <28>, <29>, <30>,
+		     <31>, <32>, <33>, <34>,
+		     <35>, <36>, <37>, <38>,
+		     <39>, <40>, <41>, <42>,
+		     <43>, <44>, <45>, <46>,
+		     <47>, <48>, <49>, <50>;
+	ngpios = <24>;
+	status = "okay";
+};
+
 &gpio2 {
 	interrupts = <53>, <53>, <53>, <53>,
 		     <53>, <53>, <53>, <53>,
@@ -199,6 +219,82 @@
 	status = "okay";
 };

+&qspi {
+	status = "okay";
+	cs-gpios = <&gpio1 17 GPIO_ACTIVE_LOW>, <&gpio0 12 GPIO_ACTIVE_LOW>;
+	num-cs = <2>;
+
+	adc@0 {
+		compatible = "microchip,mcp3464r";
+		reg = <0>; /* CE0 */
+		spi-cpol;
+		spi-cpha;
+		spi-max-frequency = <5000000>;
+		microchip,hw-device-address = <1>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+
+		channel@0 {
+			/* CH0 to AGND */
+			reg = <0>;
+			label = "CH0";
+		};
+
+		channel@1 {
+			/* CH1 to AGND */
+			reg = <1>;
+			label = "CH1";
+		};
+
+		channel@2 {
+			/* CH2 to AGND */
+			reg = <2>;
+			label = "CH2";
+		};
+
+		channel@3 {
+			/* CH3 to AGND */
+			reg = <3>;
+			label = "CH3";
+		};
+
+		channel@4 {
+			/* CH4 to AGND */
+			reg = <4>;
+			label = "CH4";
+		};
+
+		channel@5 {
+			/* CH5 to AGND */
+			reg = <5>;
+			label = "CH5";
+		};
+
+		channel@6 {
+			/* CH6 to AGND */
+			reg = <6>;
+			label = "CH6";
+		};
+
+		channel@7 {
+			/* CH7 is connected to AGND */
+			reg = <7>;
+			label = "CH7";
+		};
+	};
+
+	mmc@1 {
+		compatible = "mmc-spi-slot";
+		reg = <1>;
+		gpios = <&gpio2 31 1>;
+		voltage-ranges = <3300 3300>;
+		spi-max-frequency = <5000000>;
+		disable-wp;
+	};
+};
+
+
 &syscontroller {
 	microchip,bitstream-flash = <&sys_ctrl_flash>;
 	status = "okay";
--- a/arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts
+++ b/arch/riscv/boot/dts/sifive/hifive-unmatched-a00.dts
@@ -47,6 +47,16 @@
 		gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
 	};

+	fan1 {
+		compatible = "pwm-fan";
+		pwms = <&pwm1 2 7812500 0>;
+	};
+
+	fan2 {
+		compatible = "pwm-fan";
+		pwms = <&pwm1 3 7812500 0>;
+	};
+
 	led-controller-1 {
 		compatible = "pwm-leds";

--- a/arch/riscv/boot/dts/starfive/Makefile
+++ b/arch/riscv/boot/dts/starfive/Makefile
@@ -12,6 +12,9 @@ dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-deepcomputing-fml13v01.dtb
 dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-milkv-mars.dtb
 dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-milkv-marscm-emmc.dtb
 dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-milkv-marscm-lite.dtb
+dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-orangepi-rv.dtb
 dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-pine64-star64.dtb
+dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-starfive-visionfive-2-lite.dtb
+dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-starfive-visionfive-2-lite-emmc.dtb
 dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-starfive-visionfive-2-v1.2a.dtb
 dtb-$(CONFIG_ARCH_STARFIVE) += jh7110-starfive-visionfive-2-v1.3b.dtb
--- a/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
@@ -281,14 +281,8 @@
 	assigned-clock-rates = <50000000>;
 	bus-width = <8>;
 	bootph-pre-ram;
-	cap-mmc-highspeed;
-	mmc-ddr-1_8v;
-	mmc-hs200-1_8v;
-	cap-mmc-hw-reset;
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc0_pins>;
-	vmmc-supply = <&vcc_3v3>;
-	vqmmc-supply = <&emmc_vdd>;
 	status = "okay";
 };

@@ -298,8 +292,6 @@
 	assigned-clock-rates = <50000000>;
 	bus-width = <4>;
 	bootph-pre-ram;
-	cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
-	disable-wp;
 	cap-sd-highspeed;
 	pinctrl-names = "default";
 	pinctrl-0 = <&mmc1_pins>;
@@ -444,17 +436,6 @@
 	};

 	mmc0_pins: mmc0-0 {
-		 rst-pins {
-			pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
-					      GPOEN_ENABLE,
-					      GPI_NONE)>;
-			bias-pull-up;
-			drive-strength = <12>;
-			input-disable;
-			input-schmitt-disable;
-			slew-rate = <0>;
-		};
-
 		mmc-pins {
 			pinmux = <PINMUX(PAD_SD0_CLK, 0)>,
 				 <PINMUX(PAD_SD0_CMD, 0)>,
--- a/arch/riscv/boot/dts/starfive/jh7110-deepcomputing-fml13v01.dts
+++ b/arch/riscv/boot/dts/starfive/jh7110-deepcomputing-fml13v01.dts
@@ -11,6 +11,33 @@
 	compatible = "deepcomputing,fml13v01", "starfive,jh7110";
 };

+&mmc0 {
+	cap-mmc-highspeed;
+	cap-mmc-hw-reset;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&emmc_vdd>;
+};
+
+&mmc0_pins {
+	 rst-pins {
+		pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
+				      GPOEN_ENABLE,
+				      GPI_NONE)>;
+		bias-pull-up;
+		drive-strength = <12>;
+		input-disable;
+		input-schmitt-disable;
+		slew-rate = <0>;
+	};
+};
+
+&mmc1 {
+	cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+	disable-wp;
+};
+
 &pcie1 {
 	perst-gpios = <&sysgpio 21 GPIO_ACTIVE_LOW>;
 	phys = <&pciephy1>;
--- a/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts
+++ b/arch/riscv/boot/dts/starfive/jh7110-milkv-mars.dts
@@ -22,6 +22,33 @@
 	status = "okay";
 };

+&mmc0 {
+	cap-mmc-highspeed;
+	cap-mmc-hw-reset;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&emmc_vdd>;
+};
+
+&mmc0_pins {
+	 rst-pins {
+		pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
+				      GPOEN_ENABLE,
+				      GPI_NONE)>;
+		bias-pull-up;
+		drive-strength = <12>;
+		input-disable;
+		input-schmitt-disable;
+		slew-rate = <0>;
+	};
+};
+
+&mmc1 {
+	cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+	disable-wp;
+};
+
 &pcie0 {
 	status = "okay";
 };
--- a/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-emmc.dts
+++ b/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-emmc.dts
@@ -10,3 +10,12 @@
 	model = "Milk-V Mars CM";
 	compatible = "milkv,marscm-emmc", "starfive,jh7110";
 };
+
+&mmc0 {
+	cap-mmc-highspeed;
+	cap-mmc-hw-reset;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&emmc_vdd>;
+};
--- a/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-lite.dts
+++ b/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm-lite.dts
@@ -14,6 +14,7 @@
 &mmc0 {
 	bus-width = <4>;
 	cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+	disable-wp;
 };

 &mmc0_pins {
--- a/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110-milkv-marscm.dtsi
@@ -40,6 +40,19 @@
 	status = "disabled";
 };

+&mmc0_pins {
+	 rst-pins {
+		pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
+				      GPOEN_ENABLE,
+				      GPI_NONE)>;
+		bias-pull-up;
+		drive-strength = <12>;
+		input-disable;
+		input-schmitt-disable;
+		slew-rate = <0>;
+	};
+};
+
 &mmc1 {
 	#address-cells = <1>;
 	#size-cells = <0>;
--- a/arch/riscv/boot/dts/starfive/jh7110-orangepi-rv.dts
+++ b/arch/riscv/boot/dts/starfive/jh7110-orangepi-rv.dts
@@ -0,0 +1,76 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright (C) 2025 Icenowy Zheng <uwu@icenowy.me>
+ */
+
+/dts-v1/;
+#include "jh7110-common.dtsi"
+
+/ {
+	model = "Xunlong Orange Pi RV";
+	compatible = "xunlong,orangepi-rv", "starfive,jh7110";
+
+	/* This regulator is always on by hardware */
+	reg_vcc3v3_pcie: regulator-vcc3v3-pcie {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc3v3-pcie";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&sysgpio 62 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&gmac0 {
+	assigned-clocks = <&aoncrg JH7110_AONCLK_GMAC0_TX>;
+	assigned-clock-parents = <&aoncrg JH7110_AONCLK_GMAC0_RMII_RTX>;
+	starfive,tx-use-rgmii-clk;
+	status = "okay";
+};
+
+&mmc0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	cap-sd-highspeed;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	vmmc-supply = <&reg_vcc3v3_pcie>;
+	vqmmc-supply = <&vcc_3v3>;
+	status = "okay";
+
+	ap6256: wifi@1 {
+		compatible = "brcm,bcm43456-fmac", "brcm,bcm4329-fmac";
+		reg = <1>;
+		/* TODO: out-of-band IRQ on GPIO21, lacking pinctrl support */
+	};
+};
+
+&mmc1 {
+	cd-gpios = <&sysgpio 41 GPIO_ACTIVE_HIGH>;
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie1 {
+	status = "okay";
+};
+
+&phy0 {
+	rx-internal-delay-ps = <1500>;
+	tx-internal-delay-ps = <1500>;
+	motorcomm,rx-clk-drv-microamp = <3970>;
+	motorcomm,rx-data-drv-microamp = <2910>;
+	motorcomm,tx-clk-adj-enabled;
+	motorcomm,tx-clk-10-inverted;
+	motorcomm,tx-clk-100-inverted;
+	motorcomm,tx-clk-1000-inverted;
+};
+
+&pwmdac {
+	status = "okay";
+};
--- a/arch/riscv/boot/dts/starfive/jh7110-pine64-star64.dts
+++ b/arch/riscv/boot/dts/starfive/jh7110-pine64-star64.dts
@@ -44,6 +44,33 @@
 	status = "okay";
 };

+&mmc0 {
+	cap-mmc-highspeed;
+	cap-mmc-hw-reset;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&emmc_vdd>;
+};
+
+&mmc0_pins {
+	 rst-pins {
+		pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
+				      GPOEN_ENABLE,
+				      GPI_NONE)>;
+		bias-pull-up;
+		drive-strength = <12>;
+		input-disable;
+		input-schmitt-disable;
+		slew-rate = <0>;
+	};
+};
+
+&mmc1 {
+	cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+	disable-wp;
+};
+
 &pcie1 {
 	status = "okay";
 };
--- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-lite-emmc.dts
+++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-lite-emmc.dts
@@ -0,0 +1,22 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright (C) 2025 StarFive Technology Co., Ltd.
+ * Copyright (C) 2025 Hal Feng <hal.feng@starfivetech.com>
+ */
+
+/dts-v1/;
+#include "jh7110-starfive-visionfive-2-lite.dtsi"
+
+/ {
+	model = "StarFive VisionFive 2 Lite eMMC";
+	compatible = "starfive,visionfive-2-lite-emmc", "starfive,jh7110s";
+};
+
+&mmc0 {
+	cap-mmc-highspeed;
+	cap-mmc-hw-reset;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&emmc_vdd>;
+};
--- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-lite.dts
+++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-lite.dts
@@ -0,0 +1,20 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright (C) 2025 StarFive Technology Co., Ltd.
+ * Copyright (C) 2025 Hal Feng <hal.feng@starfivetech.com>
+ */
+
+/dts-v1/;
+#include "jh7110-starfive-visionfive-2-lite.dtsi"
+
+/ {
+	model = "StarFive VisionFive 2 Lite";
+	compatible = "starfive,visionfive-2-lite", "starfive,jh7110s";
+};
+
+&mmc0 {
+	bus-width = <4>;
+	cd-gpios = <&sysgpio 41 GPIO_ACTIVE_HIGH>;
+	disable-wp;
+	cap-sd-highspeed;
+};
--- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-lite.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-lite.dtsi
@@ -0,0 +1,161 @@
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright (C) 2025 StarFive Technology Co., Ltd.
+ * Copyright (C) 2025 Hal Feng <hal.feng@starfivetech.com>
+ */
+
+/dts-v1/;
+#include "jh7110-common.dtsi"
+
+/ {
+	vcc_3v3_pcie: regulator-vcc-3v3-pcie {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpio = <&sysgpio 27 GPIO_ACTIVE_HIGH>;
+		regulator-name = "vcc_3v3_pcie";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+};
+
+&cpu_opp {
+	/delete-node/ opp-375000000;
+	/delete-node/ opp-500000000;
+	/delete-node/ opp-750000000;
+	/delete-node/ opp-1500000000;
+
+	opp-312500000 {
+		opp-hz = /bits/ 64 <312500000>;
+		opp-microvolt = <800000>;
+	};
+	opp-417000000 {
+		opp-hz = /bits/ 64 <417000000>;
+		opp-microvolt = <800000>;
+	};
+	opp-625000000 {
+		opp-hz = /bits/ 64 <625000000>;
+		opp-microvolt = <800000>;
+	};
+	opp-1250000000 {
+		opp-hz = /bits/ 64 <1250000000>;
+		opp-microvolt = <1000000>;
+	};
+};
+
+&gmac0 {
+	starfive,tx-use-rgmii-clk;
+	assigned-clocks = <&aoncrg JH7110_AONCLK_GMAC0_TX>;
+	assigned-clock-parents = <&aoncrg JH7110_AONCLK_GMAC0_RMII_RTX>;
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&mmc1 {
+	max-frequency = <50000000>;
+	keep-power-in-suspend;
+	non-removable;
+};
+
+&pcie1 {
+	vpcie3v3-supply = <&vcc_3v3_pcie>;
+	status = "okay";
+};
+
+&phy0 {
+	motorcomm,tx-clk-adj-enabled;
+	motorcomm,tx-clk-100-inverted;
+	motorcomm,tx-clk-1000-inverted;
+	motorcomm,rx-clk-drv-microamp = <3970>;
+	motorcomm,rx-data-drv-microamp = <2910>;
+	rx-internal-delay-ps = <1500>;
+	tx-internal-delay-ps = <1500>;
+};
+
+&pwm {
+	status = "okay";
+};
+
+&spi0 {
+	status = "okay";
+};
+
+&syscrg {
+	assigned-clock-rates = <0>, <0>, <0>, <0>, <500000000>, <1250000000>;
+};
+
+&sysgpio {
+	uart1_pins: uart1-0 {
+		tx-pins {
+			pinmux = <GPIOMUX(22, GPOUT_SYS_UART1_TX,
+					      GPOEN_ENABLE,
+					      GPI_NONE)>;
+			bias-disable;
+			drive-strength = <12>;
+			input-disable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+
+		rx-pins {
+			pinmux = <GPIOMUX(23, GPOUT_LOW,
+					      GPOEN_DISABLE,
+					      GPI_SYS_UART1_RX)>;
+			bias-pull-up;
+			drive-strength = <2>;
+			input-enable;
+			input-schmitt-enable;
+			slew-rate = <0>;
+		};
+
+		cts-pins {
+			pinmux = <GPIOMUX(24, GPOUT_LOW,
+					      GPOEN_DISABLE,
+					      GPI_SYS_UART1_CTS)>;
+			input-enable;
+		};
+
+		rts-pins {
+			pinmux = <GPIOMUX(25, GPOUT_SYS_UART1_RTS,
+					      GPOEN_ENABLE,
+					      GPI_NONE)>;
+			input-enable;
+		};
+	};
+
+	usb0_pins: usb0-0 {
+		power-pins {
+			pinmux = <GPIOMUX(26, GPOUT_HIGH,
+					      GPOEN_ENABLE,
+					      GPI_NONE)>;
+			input-disable;
+		};
+
+		switch-pins {
+			pinmux = <GPIOMUX(62, GPOUT_LOW,
+					      GPOEN_ENABLE,
+					      GPI_NONE)>;
+			input-disable;
+		};
+	};
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart1_pins>;
+	status = "okay";
+};
+
+&usb0 {
+	dr_mode = "host";
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb0_pins>;
+	status = "okay";
+};
+
+&usb_cdns3 {
+	phys = <&usbphy0>, <&pciephy0>;
+	phy-names = "cdns3,usb2-phy", "cdns3,usb3-phy";
+};
--- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
+++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
@@ -38,9 +38,33 @@
 };

 &mmc0 {
+	cap-mmc-highspeed;
+	cap-mmc-hw-reset;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&emmc_vdd>;
 	non-removable;
 };

+&mmc0_pins {
+	 rst-pins {
+		pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
+				      GPOEN_ENABLE,
+				      GPI_NONE)>;
+		bias-pull-up;
+		drive-strength = <12>;
+		input-disable;
+		input-schmitt-disable;
+		slew-rate = <0>;
+	};
+};
+
+&mmc1 {
+	cd-gpios = <&sysgpio 41 GPIO_ACTIVE_LOW>;
+	disable-wp;
+};
+
 &pcie0 {
 	status = "okay";
 };